
GTA 6 at 60–120 FPS on PC from your PS5: the full guide
GTA 6 runs at 30 fps on PS5 and PS5 Pro, and Rockstar told Kotaku no 60 fps mode is coming to any launch console. SmoovPlay, a free and open-source app, streams your PS5 to a Windows PC, where your graphics card draws new frames between the real ones: 60, 90 or up to 120 fps, depending on the card and the screen.
Video guide
Before you start
The picture gets smoother, but the game still responds like 30 fps, and SmoovPlay adds about 20 ms of delay at 60 fps (36 ms at 90) on top of Remote Play. Good for story and driving, not for competitive play. The project went up on 15 November 2026 and the installer isn't code-signed yet, so your browser and Windows will warn you. Download it only from github.com/smoovplay/smoovplay, because a lookalike account exists. SmoovPlay is an independent project, not made by Sony or NVIDIA.
What you need
| Console | PS5 or PS5 Pro with GTA 6 |
|---|---|
| PC | Windows 10 or 11, 64-bit, 8 GB of memory |
| Graphics card | NVIDIA RTX 30, 40 or 50 series (AMD and Intel are experimental) |
| Disk | About 12 GB free; setup downloads about 5 GB |
| Controller | Your PS5 controller, by USB cable or Bluetooth |
| Network | Ethernet for the PS5 and the PC, or 5 GHz / 6 GHz Wi-Fi |
| Screen | 60 Hz for 60 fps, 90 Hz for 90, 120 Hz or more for 120 |
| Account | PSN, to link the PS5 once |
How it works
The PS5 still runs GTA 6 at 30 fps and sends the picture to your PC over your home network with Remote Play, through the bundled chiaki-ng app. On the PC, an AI model called RIFE draws one new frame between each pair of real ones at 60 fps, two at 90 and three at 120.
Tested on an RTX 4060
We installed SmoovPlay 0.3.11 on a PC with an RTX 4060 (8 GB). At the end of setup, Auto-detect timed the AI model on the card and chose 60 fps:
Even 60 fps is tight on this graphics card: an in-between frame takes 20.8 ms, and 60 fps leaves 16.7 ms. Expect some frames to be shown twice.
So 90 or 120 fps needs a faster card and a 120 Hz screen. One user reported 120 fps on an RTX 5080 (issue #45). We tested the install and Auto-detect, not a PS5 session.
Setup in six steps
-
Download the installer
Open the official release page and download SmoovPlay-Setup.exe under Assets.
Your browser may warn that the file isn't commonly downloaded: keep it (in Edge: ⋯ → Keep → Show more → Keep anyway). Windows then shows “Windows protected your PC”: click More info, then Run anyway.
To check the file, compare its SHA-256 with the one on the release page: Get-FileHash .\SmoovPlay-Setup.exe in PowerShell.

The official release page -
Run the setup
Setup goes Check your PC → Choose a folder → Install → Ready to play. The first page checks your graphics card, driver, memory, disk, display and network, with a fix button next to anything missing.
It takes 10 to 20 minutes and downloads about 5 GB (Python, PyTorch and NVIDIA TensorRT, from their official sources). It never asks for admin rights.

PC check on our RTX 4060 (the 120 fps line refers to the 360 Hz display) -
Turn on Remote Play on the PS5
On the PS5: Settings → System → Remote Play → Enable Remote Play.
To start the PS5 from rest mode, also open Settings → System → Power Saving → Features Available in Rest Mode and turn on Stay Connected to the Internet and Enable Turning On PS5 from Network. This part is optional.

Sony's own steps -
Link the PS5 in SmoovPlay
Open the Connect your PS5 page. It takes about 5 minutes, once. The picture comes through chiaki-ng, a free unofficial Remote Play app bundled with SmoovPlay. Sony doesn't make or support it.
- Click Open chiaki-ng. When it asks, sign in to PSN in the browser window it opens (Sony's own sign-in page), then paste the address you land on back into chiaki-ng.
- chiaki-ng looks for consoles on your network: click the one marked Automatic Registration Available and choose Yes. Not offered? Use a PIN from the PS5: Settings → System → Remote Play → Link Device (Sony's help page calls it Pair Device).
- In chiaki-ng's settings, under Video: 1080p, 60 fps (720p on a weak connection).

The Connect your PS5 page -
Play
Connect the controller to the PC. On the Play page, keep PS5 Remote Play selected and press Play. chiaki-ng opens: connect to the PS5 there and start GTA 6. The smooth picture shows in SmoovPlay's own window.
Keys in the video window
- F
- Full screen, for the lowest delay
- I
- Frame generation off and on, to compare
- S
- Stats overlay: off, minimal or detailed
- M
- Menu with every setting, live
- L
- Delay test
- Esc / Q
- Stop

The Play page -
Choose the frame rate
In Settings, Frame rate sets 60, 90 or 120 fps. Higher means more delay and more work for the card. Auto-detect times your card in about 10 seconds and suggests settings with a reason for each; Apply sets them.
GTA 6 is locked at 30 fps, so also set Smoothness → Game frame rate → 30 fps for even motion.

Settings, with Frame rate and Auto-detect
If something goes wrong
Black picture
On the PS5, open Settings → System → HDMI → Enable HDCP and turn it off, then connect again. Turn it back on later for video apps like Netflix.
Lag or stutter
Use a cable instead of Wi-Fi for the PS5 and the PC. On Wi-Fi, frames can arrive late and in bunches.
Other frame generators
Run one at a time: turn off NVIDIA Smooth Motion, AMD Fluid Motion Frames and Lossless Scaling for SmoovPlay and chiaki-ng. Other games are not affected.
Still stuck
In SmoovPlay, use Help → Copy diagnostics and paste it into an issue on the official GitHub page.
Uninstall
In Windows Settings → Apps, find SmoovPlay and choose Uninstall, or use Help → Uninstall inside the app. Your settings are kept.
Sources: SmoovPlay README · release page · Sony: Remote Play settings · Engadget, 18 Nov 2026 · our install log, 21 Nov 2026
Questions about the setup? Ask in our Discord: dsc.gg/bbirdg


















